Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
13 results
Search Results
Item Механічне травмування насіння(ЦНТУ, 2018) Скринник, І. О.; Пісарькова, І. О.; Петренко, М. М.; Скринник, И. А.; Писарькова, И. А.; Петренко, Н. Н.; Skrynnik, I.; Pisarkova, I.; Petrenko, M.Отримані залежності відношення нормальної до поверхні складової швидкості зернівки пшениці після удару по поверхні до швидкості удару (аналог коефіцієнта миттєвого тертя, від якого залежить травмування зерна) і коефіцієнта травмування насіння від швидкості удару поповерхні, кута її нахилу, матеріалу, геометрії, вологості зерна. Ці дані служать для вибору режимів роботи машин для післязбиральної обробки зерна і геометріїповерхонь їх робочих органів. Получены зависимости отношения нормальной к поверхности составляющей скорости зерновки пшеницы после удара по поверхности к скорости удара (аналог коэффициента мгновенного трения, от которого зависит травмирование зерна) и коэффициента травмирования семян от скорости удара по поверхности, угла ее наклона, материала, геометрии, влажности зерна. Эти данные служат для выбора режимов работы машин для послеуборочной обработки зерна и геометрии поверхностей их рабочих органов. The objective of the article is to establish the influence of various factors on the ratio of the normal to the surface of the wheat grain velocity component after impact on the impact velocity (the analogue of the coefficient of instant friction which influences grain damage). Another objective is the study of the dependence of damage in the process of its interaction with the surfaces of working elements of machines on speed impact with the surface, its tilt angle, material, geometry and grain humidity. It has been established that when the angle of impact of grain with the surface increases, then the normal component of velocity after impact is reduced. It determines the rate of the dynamic load on the grain. Therefore, with the increaseof the angle of impact, the proportion of damaged grains decreases. Under impact loads, the destruction (damage) of grains takes place due to stresses (tension) that occur in the place contact of grains and the surface. The tension is directly proportional to the impact force and inversely proportional to the contact area.The contact area depends on the rate of the elastic deformation of the bodies: grain – surface, which increases with the decrease of the elastic modulus of the surface materials and grains. With the increase in the velocity of impact, the restitution factor decreases because part of the energy of grain deformation goes to its local destruction. At the same time, the values of the coefficients of grain damage increase accordingly with increasing velocity (from 1 m/s to 11 m/s). When impacting with the outside surface of the cylinder, the damagecoefficient of the grain decreases with the increase in the angle of impact and the decrease in cylinder diameter. It mainly happens due to reducing the damage of the shell, as this reduces the time of contact of the grain with a convex curvilinear surface after impact. When the grain impactswith the inner cylindrical surface, the degree of grain damage increases due to the increase in the time of the slip of the grain on the surface. It was established that the percentage of grain damage is the smallest in the range of moisture of the grainsat W = 12.7-15.3%, which can be rational in the case of clearing wheat grains by machines. Reducing or increasing this rate leads to the increase in the percentage of grain damage. Therefore, grain damage during the impact can be reduced by choosing rational technological modes of operation, the geometry of surfaces of working elements of grain cleaning machines and their coatings.Item Дослідження траєкторії руху домішок в повітряному потоці(КНТУ, 2009) Онопа, В. В.; Петренко, М. М.; Кислун, О. А.; Онопа, В. А.; Опора, V.; Petrenko, М.; Kislun, О.; Onopa, V.В статті зроблено спробу дослідження траєкторії руху домішок в повітряному потоці при його очищенні, для підвищення ефективності роботи зерноочисних машин з замкнутим циклом повітряного потоку. Показано можливі траєкторії руху домішки при всмоктуванні суміжними щілинами в залежності від її попадання в одну із зон дії жалюзі. In the article the attempt research of trajectory motion of admixtures is done in the current air at his cleaning, for the increase of efficiency work grain cleaners with the reserved cycle of current air. The possible trajectories of motion admixture are rotined at suction contiguous cracks depending on its hit in one of areas of action of jalousies.Item Вплив параметрів ярусного розпушувача ґрунту на форму стінок борозни(КНТУ, 2013) Петренко, М. М.; Марченко, Т. К.; Petrenko, Nikolay; Marchenko, TatyanaВ статті розглянуто вплив параметрів ярусного розпушувача ґрунту на форму стінок борозни. Приведено формули для розрахунку розмірів зони кришення. Отримані результати розрахунків виходу зони кришення за край ножа.The aim of the study is to reduce the impact on re-working of the soil adjacent working bodies of the ripper, which is achieved by minimizing the overlapping furrows. The paper considers the influence of soil parameters tiered ripper to form the walls of the furrows, in particular, the dependence of the profile of the furrow from width knifes. Given formulas to calculate the sizes of the zone crushing before knife working body. The results of calculations exit zone crushing away from the knife depending on the width, confirmed by experimental data. The calculations for knives with cutting width in the range b = 100 ... 160 mm show that the highest yield zone crushing the edge of a knife Δb = 58 mm obtained by the working width of the knife b = 120 mm for the given soil conditions.Item Аналіз роботи пневмомеханічного висівного апарата з периферійним розташуванням комірок(КНТУ, 2013) Васильковська, К. В.; Петренко, М. М.; Гончарова, С. Я.; Vasylkovska, Ekaterina; Petrenko, Nikoly; Goncharova, SvetlanaПроведено аналіз роботи пневмомеханічного висівного апарата з периферійним розташуванням комірок. Доведено, що для гарантованого сходження зайвого насіння відцентрова сила повинна перевищувати силу тяжіння насінини. Складено диференційне рівняння руху частки в полі діючих сил, при вирішенні якого отримано залежності переміщення частки по лопатці від кута обертання диску при різних кутових швидкостях. Analysis of the design of the proposed sowing device suggests a possibility of capture, seeds, movement and dumping them , even without the use of vacuum. But guaranteed to shift the main seed furrow necessary to use more force that it be kept in the cell. Found that to guarantee convergence excess seed centrifugal force must exceed the force of gravity seed. Done differential equation of motion particle in the field of active forces in dealing with any dependencies particles moving in a pan on the angle of rotation of the disk at different angular velocities. The presence of suction power , can increase the size of the cavity passive trunk seed to 0.26 ... 0.30 radians in angular velocity of the disk 30 ... 25 radians per second. This will guaranteed to remove those extra seeds , as they move around the pan more than half their own diameter. A basic seed, thanks to the force of suction , securely held in a cell and transported to the area of a disk reset.Item Модель зміни шпаруватості псевдорозрідження шару насіння на каскадах зерносушарки(КНТУ, 2008) Петренко, М. М.; Скриннік, І. О.; Скриннік, М. О.; Богатирьов, Д. В.; Кислун, О. А.В статті розглянуто гідродинамічну модель псевдорозрідження насіння в зерносушарці каскадного типу. Наведені дослідження, які дозволяють теоретично визначити закономірності зміни порозності псевдорозрідженого шару відносно крупних частинок в залежності від зміни швидкості газу в апараті. In the article motion of seed is considered for to the cascades of the installation for dry grain in the booling layer. Researches which allow in theory to define the structural parameters of dryer taking into account the features of motion of seed are resulted.Item Ефективність уловлювання шкідників пневматичною насадкою пневмодезинсектора(КНТУ, 2010) Петренко, М. М.; Онопа, В. А.; Кислун, О. А; Petrenko, М.; Onopa, V.; Kislun, О.В статті розглянуто роботу пневматичної насадки пневмодезинсектора при збиранні шкідників з насаджень картоплі. Розглянуто вплив дії всмоктуючого факел пневматичної насадки пневмодезинсектора на ефективність уловлювання шкідника підчас реагування його небезпеку. За допомогою пакету прикладних програм на ПЕОМ, отримали графічну залежність теоретичного значення ефективності (Е) уловлювання від швидкості руху агрегату Vагр. In the article work of pneumatic attachment of pnevmodezinsektora is considered at collection of wreckers from planting of potato. Influence of action is considered vsyvayuschego torch of pneumatic attachment of pnevmodezinsektora on efficiency of catching of wrecker of the vovrem'ya reacting him on a danger. With a help to the application package on PEOM, got graphic dependence of theoretical value of efficiency (Е) catching from the rate of movement of asm Vagr.Item Гідродинамічна модель процесу сушіння насіння сільськогосподарських культур для продовольчих потреб(КНТУ, 2011) Скриннік, І. О.; Федотова, М. О.; Петренко, М. М.; Кислун, О. А.; Богатирьов, Д. В.; Skrunnik, I.; Fedotova, M.; Petrenko, M.; Kyslun, O.; Bogatyryov, D.Наведено теоретичні дослідження для визначення параметрів киплячого шару в залежності від параметрів сушарки для отримання раціональних параметрів процесу сушіння. Теоретичні дослідження направленні на зменшення енергетичних витрат. An theoretical study to determine the parameters of a boiling layer, depending on drying parameters for rational parameters of the drying process. Theoretical studies directed to reduce energy costs.Item До обґрунтування параметрів пневмомеханічного висівного апарата з периферійним розташуванням комірок для точного висіву насіння просапних культур(КНТУ, 2011) Петренко, М. М.; Васильковський, М. І.; Васильковська, К. В.; Petrenko, M.; Vasylkovskyi, M.; Vasylkovska, K.В статті обґрунтовані умови збільшення продуктивності оригінального пневмомеханічного висівного апарата з диском, на якому периферійно розташовані комірки для точного висіву насіння просапних культур за рахунок збільшення швидкості обертання комірок висівного елементу за умови збереження їх якісного заповнення. In the article reasonable terms of increase of the productivity of original pneumomassage sowing vehicle with a disk, on that the peripherally located cells for seed-spacing of seed of the cultivated cultures due to the increase of velocity of circulation of cells of sowing element on condition of maintenance of them quality filling.Item Суміщення технологічних операцій у виробництві олії(КНТУ, 2011) Васильковський, О. М.; Сало, В. М.; Петренко, М. М.; Васильковський, Я. С.; Vasilkovskiy, O.; Salo, V.; Petrenko, M.; Vasilkovskiy, Y.В статті наводиться один з варіантів удосконалення технологічної лінії по виробництву олії з термічною обробкою насіння соняшнику, перевагою якого є суттєве зменшення металоємності, енергоємності та габаритів пневморешітного сепаратора. Вказаний ефект досягається завдяки використанню оригінального робочого органу, що дозволяє реалізувати суміщення кількох технологічних операцій. The article provides an option to improve the technological line for production of oil from heat treatment of sunflower seeds, the advantage of which is a significant reduction in metal, energy and dimensions pneumatic-grate separator. The indicated effect is achieved by using the original working body to implement the combination of several technological operations.Item Теоретичні дослідження процесу дозування насіння під час висіву пневмомеханічними апаратами(КНТУ, 2012) Свірень, М. О.; Петренко, М. М.; Богатирьов, Д. В.; Павленко, І. І.; Sviren, M.; Petrenko, M.; Bohatyrov, D.; Pavlenko, I.Виділення одиничного насіння із загальної маси є початковим основоположним процесом у формуванні однорідного потоку. Від виконання цього процесу залежать всі наступні етапи дозування, які в кінцевому підсумку визначають якість роботи висівного апарату. Важливість ефективного виділення одиничного насіння від загальної маси полягає і в тому, щоб на основі вивчення цього процесу можна розробляти конструкції більш універсальних апаратів для висіву насіння різних культур, реалізуючи перспективні технології механізації в рослинництві. Дозування насіннєвого матеріалу сучасним висівних апаратів повинно також враховувати реальні умови виконання посіву. Isolation of a single seed from the masses is the initial fundamental process in the formation of a homogeneous flow. From this process, depend all the subsequent stages of the dosage, which ultimately determine the quality of the sowing machine. The importance of effective allocation of a single seed of the total mass lies in the fact that by studying this process can develop designs more versatile machines for sowing different crops, implementing advanced technology of mechanization in crop production. Dosage modern seed sowing machines should also take into account the actual conditions of crop performance.