Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
8 results
Search Results
Item Використання мікродугового оксидування при зміцненні деталей з алюмінієвих сплавів, відновлених пластичним деформуванням(ЦНТУ, 2017) Кулєшков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Матвієнко, О. О.; Kuleshkov, Y.; Krasota, M.; Rudenko, T.; Matvienko, A.У статті приведений аналіз можливості використання нового способу зміцнення - мікродугового оксидування для підвищення зносостійкості деталей, виготовлених з алюмінієвих сплавів, зокрема корпусів шестеренних насосів типу НШ. У роботі викладена сутність процесу зміцнення деталей мікродуговим оксидуванням, представлені основні фізико-механічні характеристики зміцнюючого покриття. Відзначено, що міцність зчеплення і механічні властивості покриття багато в чому залежать від стану поверхні, що зміцнюється, зокрема від методу попередньої обробки. При цьому встановлено, що зміцнюючі покриття після пластичного деформування деталей мають вищу міцність зчеплення, твердість і більшу товщину. У роботі представлені основні відомості про мікродугове оксидуванні, які на думку авторів будуть сприяти застосуванню маловивченого способу зміцнення в ремонтному виробництві. The objective of the research is to analyse the scientific and technical information on hardening of parts of aluminium alloys by micro-arc oxidation, particularly the parts, which were repaired by hot plastic deformation. This article presents the analysis of the possibility to apply a new method of hardening of working surfaces of parts by micro-arc oxidation to increase wearability of working surfaces of the parts made of aluminium alloys, in particular the bodies of gear pumps. The work presents the essence of the process of hardening of details by micro-arc oxidation and the main physical and chemical characteristics of the hardening coating. It was stated that the adhesive strength and mechanical characteristics of the coating largely depend on the condition of the surface under hardening, in particular on the method of preparatory processing. It was established that the hardening coating of metal after plastic deformation gets better adhesive strength, thickness and hardness. The work presents basic information on micro-arc oxidation which will facilitate further application of the hardening method in repair industry.Item Аналіз теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса(ЦНТУ, 2017) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Красота, М. В.; Руденко, Т. В.; Kuleshkov, Y.; Magonets, E.; Kuleshkova, K.; Krasota, M.; Rudenko, T.В статті наведені результати аналізу теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса. Встановлені теоретичні залежності об’єму відсіченої порожнини від параметрів зубчастого зачеплення, а також від положення точки зачеплення на лінії зачеплення шестерень насоса. Отримані теоретичні залежності дозволяють визначити геометричні параметри відсіченої порожнини, при яких виключається явище компресії робочої рідини. Виключення компресії досягнуто завдяки використанню зубчастого зачеплення з асиметричною лінією зачеплення. В роботі вказані недоліки існуючих теоретичних досліджень і вказані напрямки подальшого їх розвитку.The objective of research is to analyze scientific and technical information on the results of theoretical studies of the geometric parameters of the cut-off housing of the gear pump and to determine future direction of research of the processes that take place in the cut-off housing and to formulate the scientific hypothesis of the research. The article presents the results of the analysis of theoretical studies of geometric parameters of the cut-off housing of the gear pump. The theoretical dependences of the volume of the housing on the parameters of toothing were established as well as the position of the point of engagement on the line of contact of a gear pump. The theoretical dependences allow determining geometrical parameters of the cut-off housing which eliminate the phenomenon of the working fluid compression. The avoidance of compression is achieved through the use of toothing with asymmetrical engagement line. The work indicates the shortcomings of existing theoretical research and presents the directions of further development. It was established that one of the possible ways to reduce the impact of the compression of the working fluid in the cut-ff housing is to use toothing with asymmetric line engagement.Item Аналіз математичних моделей втрат робочої рідини через радіальний зазор шестеренного насоса типу НШ(КНТУ, 2006) Кулєшков, Ю. В.; Матвієнко, О. О.; Kuleshkov, J.; Matvienko, O.В статті розглянуто відомі математичні моделі втрат робочої рідини через радіальний зазор шестеренного насоса типу НШ і зроблено аналіз їх переваг та недоліків. In the article the mathematical models known working fluid leaks through the radial clearances of gear pumps and the analysis of their strengths and weaknesses.Item Методика стендових випробовувань шестеренного насоса(КНТУ, 2011) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвієнко, О. О.; Титов, Ю. А.; Kuleshkov, J.; Rudenko, T.; Krasota, M.; Matvienko, A.; Titov, J.Розроблена програма досліджень, яка включала методики дослідження основних технічних характеристик НШ для різних значень тиску, робочого об’єму насоса і частоти обертання, і перевірку ступеня збігу основних теоретичних положень і висновків з результатами, отриманими експериментальним шляхом. Розглянуто методики випробувань шестеренних насосів з регульованою подачею, наведено будову та характеристика дослідного обладнання. Викладено методику обробки даних, отриманих при проведенні експериментальних досліджень. The program of researches including techniques of research of basic tehniche-skih of characteristics gear-type pumps for different values of pressure, working volume of the pump and frequency of rotation, check of degree of coincidence of the basic theoretical positions and conclusions with the results, luchen th experimentally is developed. Techniques of tests gear-type pumps from a reguliro-bathroom are considered by giving, the device and the characteristic of the research equipment is resulted. The technique of the data processing, the experimental researches received at carrying out is stated.Item Аналіз причин виникнення шуму в гідроприводах(КНТУ, 2011) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Тітов, Ю. О.; Kuleshkov, J.; Rudenko, T.; Krasota, M.; Titov, J.В статті наведений аналіз джерел шуму в гідравлічних приводах транспорту та технологічного устаткування. Проаналізовано основні параметри, за якими оцінюють рівень шуму в гідроприводах, дано їх визначення. Визначено умови роботи гідроприводу, його основні переваги, а також коливальні процеси, що виникають при експлуатації. Представлена класифікація шумів у гідроприводі за походженням дана їх характеристика. Встановлено основні шляхи поширення шуму у гідроприводі. Зроблено висновок, що механічний шум найбільш характерний для гідросистем з шестеренними насосами. Намічено основні напрямки досліджень по зменшенню механічного шуму у шестеренних насосах. In article the analysis of sources of noise in a hydraulic drive of transport and the process equipment is resulted. Key parameters on which the noise estimation in hydraulic actuators is carried out are analysed, their definition is made. Hydraulic actuator working conditions, its basic advantages are defined, and also oscillatory processes that occur at operation are established. Classification of noise in a hydraulic actuator by origin is presented, their characteristic is given. The basic ways of distribution of noise to hydraulic actuators are established. The conclusion that mechanical noise most typical for hydraulic actuators with pumps is drawn. The basic directions of researches on reduction of mechanical noise in pumps are planned.Item Дослідження поведінки математичної моделі питомого робочого об’єму шестеренного насосу типу НШ від параметрів зубчатого зачеплення(КНТУ, 2010) Кулєшков, Ю. В.; Черновол, М. І.; Руденко, Т. В.; Гуцул, В. І.; Осин, Р. А.; Kuleshkov, U.; Chernovol, M.; Rudenko, T.; Guzul, V.; Osin, R.Одним з перспективних напрямків подальшого вдосконалення конструкції шестеренних насосів гідроприводу сільськогосподарських машин є підвищення його питомих показників подачі. Дослідження розробленої математичної моделі питомого робочого об'єму шестеренного насоса дозволило визначити ступінь впливу параметрів зубчатого зачеплення на питомий робочий об'єм шестеренного насоса. One of the promising directions of further improving the design of gear pumps hydraulic drive farm machinery is increasing its specific indicators filing. The study developed a mathematical model of the specific work of gear pumps possible to determine the degree of influence of the parameters of the gear ratio on the working volume of gear pumps.Item Аналіз існуючих уявлень про механізм виникнення пульсацій миттєвої подачі шестеренного насоса(КНТУ, 2014) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Осін, Р. А.; Кулєшкова, К. Ю.; Kuleshkov, Yuriy; Rudenko, Tymofiy; Krasota, Mykhailo; Osin, Ruslan; Kuleshkova, KseniaВ статті наведені теоретичні дослідження спрямовані на розробку фізичної моделі та відповідної їй аналітичної залежності миттєвої подачі, що дозволяють пояснити причини і механізм пульсації миттєвої подачі шестеренного насоса. The objective of the research is the elaboration of a mathematical physical model of immediate flow of a gear pump which allows explaining the mechanism of occurrence of pulsations of immediate flow and pressure in the process of work cycle of a gear pump. We suggested a new physical model and a corresponding mathematical model of the process of immediate flow of a gear pump which show that the process of flow consists of two simultaneously occurring processes: the process of volume reduction which stimulates flow and the process of volume increase which blocks flow. The suggested mathematical model allows explaining the pulsating character of immediate flow of a gear pump due to the peculiarities of changes of conditional radiuses which connect the centres of gears with the contact point and while rotation they block the flow.Item Экспериментальные исследования спектров шума шестеренного насоса с косозубым зацеплением(КНТУ, 2015) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвиенко, О. О.; Осин, Р. А.; Kuleshkov, Y.; Rudenko, T.; Krasota, M.; Matvienko, O.; Osin, R.; Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвієнко, О. О.; Осін, Р. А.В статье приведены результаты испытаний шумовых характеристик экспериментального шестеренного насоса с косозубым зацеплением. Исследованы уровни звука, спектры шума. экспериментального насоса с косозубым зацеплением, а также серийного насоса аналогичного типоразмера при разных режимах их работы. Выполнен сравнительный анализ шумовых характеристик насосов при разных нагрузках с целью оценки эффективности использования косозубых зацеплений в шестеренных насосах с точки зрения снижения шума. В статті наведені результати випробовувань шумових характеристик експериментального шестеренного насоса з косозубим зачепленням. Досліджено рівні звуку, спектри шуму експериментального шестеренного з косозубим зачепленням, а також серійного насосу аналогічного типорозміру при різних режимах їх роботи. Виконано порівняльний аналіз шумових характеристик насосів при різних навантаженнях з метою оцінки ефективності використання косозубих зачеплень в шестеренних насосах з точки зору зниження шуму. The objective of the work is the experimental testing of the noise level by the lines of spectrum of the experimental gear pump with helical toothing and the comparison with the noise level of a serial pump. The article presents the results of tests of noise characteristics of the experimental gear pump with helical toothing. The levels of noise, noise spectrums of the experimental gear pump with helical toothing and a serial pump of the analogical size with straight toothing were investigated using different operating modes. The comparative analysis of noise characteristics of the pumps under different load was carried out in order to estimate the efficiency of using helical toothing in gear pumps from the point of view of noise reduction. Experiments of the noise level of a gear pump with helical toothing showed that with the increase of pressure of hydraulic fluid the level of noise slowly increases from 1,5 to 6 dB depending on speed mode. The highest noise level of a pump with helical toothing (91,5 dB ) is noticed under the pressure of 16,0 MPa and rotation frequency n=2400 revolutions per minute. The comparative analysis of the experimental pump and a serial pump enables to state that the noise level of the experimental pump is lower in all operating modes compared to the serial pump. During tests it was marked that the noise level of the stand which is a barrier is quite high and under some operating modes it is close to the noise level of the experimental pump on the stand.