Browsing by Author "Salo, V."
Now showing 1 - 20 of 27
Results Per Page
Sort Options
Item Experimental Estimate of the Efficiency of Basic Tilling by Chisel Equipment in the Conditions of Soil Compaction(КНТУ, 2014) Leschenko, S.; Salo, V.; Petrenko, D.; Лещенко, C. М.; Сало, В. М.; Петренко, Д. І.The work discloses experimental estimates of the efficiency of basic boardless tilling by chisel equipment in the conditions of considerable compaction of the plough layer. The factors that prove expediency of soil chiselling and the outcomes of introduction into technological growing processes of this resource saving tilling were presented. The design of chisel blade with vertical and horizontal deformators was suggested. The results of experimental research of the designed chisel showed influence of speed parameters and a set of additional working organs on the indicators of soil grinding were given. Робота присвячена експериментальній оцінці ефективності основного безвідвального обробітку ґрунту чизельними знаряддями в умовах значного переущільнення орного горизонту. Наведені фактори, що доводять доцільність проведення чизелювання ґрунтів та наслідки впровадження в технологічні процеси вирощування цього ресурсозберігаючого способу основного обробітку. Запропоновано конструкцію чизельної лапи з вертикальними та горизонтальними деформаторами. Приведені результати експериментальних досліджень розробленого чизеля в ході яких встановлено вплив швидкісних параметрів та набору додаткових робочих органів на якісні показники подрібнення ґрунту.Item Адаптація операцій чизельного обробітку до складних ґрунтово-кліматичних умов Центральної України(Копіцентр «Документ-сервіс», 2015) Лещенко, С. М.; Сало, В. М.; Васильковський, О. М.; Петренко, Д. І.; Дейкун, В. А.; Leschenko, S.; Salo, V.; Vasilkovskiy, O.; Petrenko, D.; Deikun, V.Традиційна система основного обробітку ґрунту, яка базується на застосуванні ґрунтообробних знарядь полицевого типу, останнім часом втрачає свої позиції і поступається безполицевим способам обробітку. В роботі окреслені проблеми реалізації технологій безвідвального обробітку ґрунту в рослинництві. Встановлено ряд причин, як не дозволяють в повній мірі впровадити ресурсозберігаючі методи під час операцій основного обробітку ґрунту в Україні. На основі критичного аналізу розроблено конструкцію вдосконаленого комбінованого чизеля із основними робочими органами, які поєднують роботу горизонтальних та вертикальних деформаторів. На основі методики планування експерименту проведено експериментальну перевірку якості роботи комбінованого чизеля. Встановлено раціональні параметри та режими роботи машини для ґрунтово-кліматичних умов України. На основі проведеного експерименту надані рекомендації щодо виробництва чизельних ґрунторозпушувачів. Traditional primary tillage being based on the use of tillage implements of mouldboard type, is currently losing its position and forgoes mouldboardless methods of cultivation. This paper outlines the implementation problems of mold technologies in crop cultivation. A number of reasons has been defined that don’t allow to fully implement saving techniques during basic soil tillage operations in Ukraine. Based on the critical analysis developed the advanced design combined with chizel basic working tools that combine work horizontal and vertical deformators has been worked out. Based on the experimental design technique has been experimentally tested the quality of the combined chizel. Rational parameters and modes of the machine for soil and climatic conditions of Ukraine have been established. Based on the experiment having been conducted the recommendations on chisel rippers production have been given.Item Аналітична оцінка якості пневмосепарації на основі алгоритму функціонування зерноочисних машин(КНТУ, 2012) Лещенко, С. М.; Сало, В. М.; Васильковський, О. М.; Богатирьов, Д. В.; Отт, В. В.; Leschenko, S.; Salo, V.; Vasil'kovskiy, А.; Bogatirev, D.; Ott, V.В статті проведено аналітичну оцінку якості пневмосепараційного процесу на основі алгоритму функціонування зерноочисних машин загального призначення. Запропоновано системний аналіз вхідних та вихідних чинників системи, що впливають на кількісні і якісні показники сепарації, які отримані з використанням методики В.Е. Саітова. Після побудови алгоритму функціонування зерноочисної машини проведено оцінку якості роботи та витрат енергії. Використовуючи теорію ймовірностей отримані залежності по оцінці ефекту очистки виходячи з рівня виділення компонентів кожної фракцій по етапах очищення. Наведені дослідження доводять, що використання замкненого повітряного потоку комбінованої дії (послідовне продування похилим та вертикальним потоком) від одного джерела дозволяє підвищити якість сепарації без суттєвого підвищення енерговитрат. In the article the analytical estimation quality of air cleaner process is conducted on the basis of algorithm functioning of grain cleaners of the general setting. The analysis systems of entrance and initial factors is offered systems. Influencing on quantitative and quality indexes separations that is got with the use of methodology V. Saitov. After the construction algorithm functioning of grain cleaner the estimation of quality work and charges of energy is conducted. Using the theory of chances the got dependences as evaluated by the effect of cleaning coming from the level of selection of components each factions on the stages cleaning. The brought researches over prove that the use of the reserved current air of the combined action(successive blowing out by a sloping and vertical stream) from one source allows to improve quality separation without the substantial increase of expenses energy.Item Вивчення конструктивно-технологічних параметрів робочих органів комбінованих чизельних глибокорозпушувачів(ЦНТУ, 2019) Лещенко, С. М.; Сало, В. М.; Петренко, Д. І.; Васильковський, О. М.; Лещенко, С. Н.; Петренко, Д. И.; Васильковский, А. М.; Leshchenko, S.; Salo, V.; Petrenko, D.; Vasylkovskyi, O.В роботі проводиться систематизація основних найбільш поширених робочих органів чизельних глибокорозпушувачів з критичною оцінкою їх конструктивно-технологічних параметрів. Доводиться, що незважаючи на конструктивну подібність чизельних лап з прямим стояком, що використовуються в серійних ґрунтообробних агрегатах, конструкцію цих робочих органів не можна вважати повністю обґрунтованою, що насамперед відноситься до використання на лапах додаткових робочих органів і елементів та можливості аналітично розрахувати і практично забезпечити задану глибину суцільного обробітку. Наведені залежності, які дозволяють знайти критичну глибину чизельного обробітку, величину зон деформацій, глибину суцільного обробітку та встановлені значення рекомендованих конструктивних параметрів чизельної лапи з прямим стояком. В работе проводится систематизация основных наиболее распространенных рабочих органов чизельных глубокорыхлителей с критической оценкой их конструктивно-технологических параметров. Доказывается, что несмотря на конструктивное сходство чизельных лап с прямой стойкой, используемых в серийных почвообрабатывающих агрегатах, конструкцию этих рабочих органов нельзя считать полностью обоснованной, что прежде всего относится к использованию на лапах дополнительных рабочих органов, элементов и возможности аналитически рассчитать и практически обеспечить заданную глубину сплошной обработки. Приведены зависимости, позволяющие найти критическую глубину чизельной обработки, величину зон деформаций, глубину сплошной обработки и установленные значения рекомендуемых конструктивных параметров чизельных лап с прямой стойкой. Gradual abandonment of application of erosion-hazardous tools is a worldwide trend in soil tillage. The tools include classic ploughs, machines and equipment with spherical disks, milling units and the like. The article deals with the systematization of the most widespread operating elements of chisel deep-tillers with a critical assessment of their structural and technological parameters. The objective of the work is to study the structural and technological parameters of chisel blades of combined deep-tillers for general purpose, depending on the layout of the unit and the structure of the main operating elements. Regardless of the generally accepted tendency to abandon erosion-hazardous tools at the basic tillage stage, chisel deep-tillers, which are an effective substitute for classic heap plowing, do not have fully substantiated functional schemes and recommendations for the design of both major and additional operating elements. At the Department of Agricultural Engineering of Central Ukrainian National Technical University, a functional scheme, design documentation and a series of hinged chisel aggregates were developed. The main operating element of the developed machines is a straight-leg chisel blade, in which, as additional horizontal deformers, which provide alignment of the bottom of the furrow and better pruning of the root systems of plants, the flat wings are set at a certain angle to the direction of movement, and in combination with the chisel, provide ground clearance in the horizontal plane. Taking into account certain generally accepted assumptions and using known dependencies, the formulas were obtained for theoretical substantiation of rational construction and specific parameters of the proposed chisel blade. As a result of the work, the possibility of using operating elements of chisel deep-tiller blades paws with a straight leg and an additional horizontal deformer was proved. On the basis of the conducted research it is established that in loamy soil conditions chisel deep-tillers provide performance within agrotechnical requirements at the velocity of movement of the unit up to 2.5 m/s, the angle of installation of the chisel to the bottom of the furrow is 25… 30º, chisel length is 0.26…0.35 m at the distance between rows of the operating elements in the longitudinal direction 0.45…0.55 m.Item Визначення еквівалентної проекції висоти перетину барабана з непарною кількістю ножів(КНТУ, 2016) Богатирьов, Д. В.; Сало, В. М.; Кислун, О. А.; Bogatyrov, D.; Salo, V.; Kuslyn, О.Стаття присвячена теоретичному дослідженню впливу еквівалентної проекції висоти bек на точність визначення сили опору повітря барабану з ножами. Зроблено спробу уточнити площу опору в залежності від кутового положення та кількості ножів барабана котка-подрібнювача. Дослідження впливу еквівалентної проекції висоти на точність опису сили опору повітря барабану з непарною кількістю ножів показали, що відносна похибка зменшується у 1,5 рази, що пояснюється виключенням впливу невизначеності початкового кутового положення барабану. During the last few years Ukraine was filled with nontraditional and in some cases unknown technologies of crop science. The changes started by using imported harvesters which left practically all residues on the field. This practice allowed increasing the productivity of picking processes and to shorten the terms of harvest period but there appeared the problem of further processing of plant residues. The Ukrainian producers chose the simplest way to solve it and used disc equipment for soil cultivation. As a result the structure of surface soil was damaged, valuable agro-technical aggregates were mashed, which led to their transformation into dusty unstructured condition. There was also overtamping of subsoil, disfunction of the processes of aeration and infiltration, decrease of the storage of productive soil water in lower levels. Special machines are usually used in these cases abroad which are debris pulverisers. In Ukraine these machines are not well known, expensive and perceived by agricultural producers as part of the technological process which needs extra costs and not obligatory. Besides, according to the special design of every of these machines they do not provide necessary pulverization in the traditional for Ukraine production technologies. In order to determine the accurate draught of the crimp-roller it is necessary to take into account the force to overcome air resistance. The article presents theoretical research of the influence of introduction of equal-area projection of the height on the accuracy of calculation of the resistance power of the air of the cylinder drum with blades. The effort was made to specify the area of resistance depending on the angle setting and the number of blades of the crimp-roller. Research of introduction of the equal-area projection of the height on the accuracy of description of the power of air resistance of the crimp-roller showed that the fractional error decreases in 1,5 times. This is explained by the absence of the influence of uncertainty of the initial angle setting of the cylinder drum.Item Визначення параметрів та ефективність роботи додаткових робочих органів глибокорозпушувачів(ЦНТУ, 2022) Лещенко, С. М.; Сало, В. М.; Васильковський, О. М.; Петренко, Д. І.; Leshchenko, S.; Salo, V.; Vasylkovskyi, О.; Petrenko, D.роботі проведено огляд і аналіз існуючих додаткових робочих органів комбінованих глибокорозпушувачів серійних машин. Встановлено, що питання оцінки ефективності роботи додаткових робочих органів глибокорозпушувачів та пошук їх раціональних конструктивно- технологічних параметрів є недостатньо дослідженим і потребує практичного вирішення. Запропоновано використання у якості додаткових робочих органів спарених зубчастих котків та визначено їх окремі конструктивні параметри. Наведені результати польових досліджень ефективності роботи спарених зубчастих котків у агрегаті із комбінованим чизельним глибокорозпушувачем. Встановлено, що при швидкості роботи 7…8 км/год та рівномірній дії на ґрунт обома котками на важких і середніх суглинкових ґрунтах досягається показник кришення ґрунту 70-75%. The article presents an overview and analysis of existing additional operating parts of combined deep tillers of serial machines. It was established that the issue of assessing the effectiveness of additional operating parts of deep tillers and the search for their rational structural and technological parameters is insufficiently studied and needs practical solution. The most versatile operating part for high-quality work of deep tillers can be a paired toothed roller. Having studied its design parameters and operating modes, it is possible to get clear recommendations regarding its use. An improved design of the Tandem Spiked toothed roller type with mechanical adjustment is proposed, as such rollers have a much simpler shape of teeth and a smaller cross-section of each tooth. The dependences for the calculation of certain design parameters of the roller, namely its diameter, length and coefficient of volume deformation of the soil, are given based on the fact that the roller performs two functions – compaction of the lower layers of the soil and crushing of clods and intensive mixing of the upper horizons. To determine the rolling force on the soil surface, we use the relationship that includes the weight of the roller, the volume deformation coefficient of the soil, the grip width of the roller and its diameter. Field studies to assess the efficiency of paired toothed rollers ere carried out. For the effective operation of combined deep tillers of the soil, it is necessary to use additional operating parts, which should additionally grind large particles and partially mix and distribute plant residues. It is most expedient to use paired toothed rollers with mechanical adjustment as additional operating parts under difficult working conditions. At the stage of substantiating the design parameters of paired toothed rollers, it is enough to take into account the required angle of the soil roller's girth and the average value of the soil deformation depth. This will allow getting actual value of the working diameter of the roller and calculate the force of the roller rolling over the soil surface. During field studies of the operation of combined deep tillers with a paired toothed roller, it was established that when working with two toothed rollers at a working speed of 7.2...8.2 km/h, the qualitative indicator of soil crushing is at the level of 70...75%, which significantly exceeds the qualitative indicators of the work of foreign machines of a similar design under the same operating conditions.Item Визначення умови руху неперервного потоку рослинних решток по стеблевідводу сошника(КНТУ, 2012) Лузан, О. Р.; Сало, В. М.; Лузан, П. Г.; Гончарова, С. Я.; Luzan, Е.; Salo, V.; Luzan, Р.; Goncharova, S.В статті проведений теоретичний аналіз умов руху неперервного потоку рослинних решток по стеблевідводу сошника для прямої сівби зернових культур. Отримані залежності для визначення сприятливих умов руху рослинних решток по горизонтальній поверхні стеблевідводу та умов утримання рослинних решток на ньому. In this paper a theoretical analysis of the traffic conditions of continuous flow of crop residue on the device for removing stalks opener for direct sowing of grain crops. The dependencies for the determination of favorable traffic conditions of plant residues on the horizontal surface of the device for removing the stems and conditions of retention of crop residues on it.Item Вплив зносу елементів конструкції сошників на їх тяговий опір(КНТУ, 2012) Мачок, Ю. В.; Сало, В. М.; Аулін, В. В.; Сабірзянов, Т. Г.; Лузан, П. Г.; Machok, Yu.; Salo, V.; Aulin, V.; Sabirzyanov, T.; Luzan, P.Стаття присвячена вивченню питання впливу стану леза полозу на тяговий опір полозкового сошника зернової сівалки. Розглянуто три можливих варіанти стану леза: стандартне загострене, незміцнене незагострене, незагострене зміцнене зносостійкими композиційними матеріалами. Отримано аналітичні залежності тягового опору полозкового сошника від зміни параметрів леза та їх графічна інтерпретація. This article is devoted to studying the question of influence of blade runner on traction resistance runner coulter seed drill. Three possible options of blade: Standard pointed, unstable Unsharpened, Unsharpened strengthened durable composite materials. Analytical dependences and their graphical interpretation of the traction skid resistance of your settings opener blade.Item Вплив конструктивно-технологічних параметрів комбінованого глибокорозпушувача на обробіток ґрунту(КНТУ, 2016) Лещенко, С. М.; Сало, В. М.; Петренко, Д. І.; Leschenko, S.; Salo, V.; Petrenko, D.В роботі обґрунтовується необхідність проведення глибокого розпушування ґрунту чизельними знаряддями для покращення агрегатного стану, інфільтраційних властивостей, руйнування ущільненої підорної підошви та реалізації основ ґрутозахисних та енергоощадних технологій. На основі оцінки конструкцій основних робочих органів чизельних знарядь зроблено висновок про доцільність використання розпушувальних лап із прямим стояком за умов введення в їх конструкцію додаткових рушіїв. В результаті проведених досліджень підтверджено вплив додаткових робочих органів та елементів на якість кришення ґрунту і витрати енергії. Запропоновано вдосконалену конструкцію чизельної лапи із додатковими рушіями. Представлені окремі результати теоретичних та експериментальних досліджень вдосконаленого комбінованого чизеля, які підтверджують його ефективність та можливість використання в складних ґрунтово-кліматичних умовах України. Встановлено, що при проведенні обробітку важкого і середнього суглинку вдосконаленим комбінованим чизелем можна досягти якісного показника кришення ґрунту на рівні 70-75%. Розроблені рекомендації по практичному використанню запропонованого чизельного глибокорозпушувача. The article gives suggestion on the improvement of deep tillage of soil with the help of combined chisel equipment. Taking into account the existing technologies of tillage and technical equipment for the realization of the above-mentioned operations we concluded that it is reasonable to give up traditional moldboard tillage. Taking into consideration the experience in the agrarian sphere of the developed countries and researchers’ findings the deep tillage by the combined chisel equipment can be the starting point of energy saving and soil protecting technologies. Considering the specificity of soils and variety of requirements for technical support of chisel tillage, the issue of improvement of chisel tilling equipment needs effective scientific solving, including the process of adaptation of the existing designs to certain conditions. On the basis of the research findings we proved a positive influence of the additional working parts and elements on the quality of soil pulverization and energy costs. The improved design of a chisel sweep with additional deformers was suggested. In the function of the additional working parts of the combined chisel it is recommended to use a coupled crosskill roller with straight teeth which functions as supportive and provides breaking big lumps and equal distribution of useful residues at the set depth. The presented results of theoretical and experimental research of the improved combined chisel prove its efficiency and enable its application in difficult soil and climatic conditions of Ukraine. It was specified that cultivation of hard and medium clay loam by a combined chisel increases the quality indicator of soil pulverization at the level of 70-75%. The recommendations for practical application of the suggested tilling appliance were developed.Item Вплив конструктивно-технологічних параметрів робочих органів глибокорозпушувача на тяговий опір(ЦНТУ, 2018) Лещенко, С. М.; Сало, В. М.; Петренко, Д. І.; Васильковський, О. М.; Лещенко, С. Н.; Петренко, Д. И.; Васильковский, А. М.; Leshchenko, S.; Salo, V.; Petrenko, D.; Vasylkovskyi, O.В роботі оцінюється вплив конструктивно-технологічних параметрів робочих органів комбінованих глибокорозпушувачів на тяговий опір агрегатів. Доводиться, що використання раціональної формули Горячкіна для аналітичного визначення тягового опору глибокорозпушувачів, у традиційному її представленні є недоречним, оскільки чизельні агрегати здійснюють принципово іншу технологічну операцію порівняно з полицевим плугом. Запропоновано методику визначення тягового опору чизельних знарядь з врахуванням зон деформацій від конструктивних елементів чизельних лап. З практичної точки зору проаналізовано вплив деяких конструктивних елементів глибокорозпушувача на питомий опір ґрунту та проведено оцінку витрати пального в залежності від комплектування агрегату. В работе оценивается влияние конструктивно-технологических параметров рабочих органов комбинированных глубокорыхлителей на тяговое сопротивление агрегатов. Доказывается, что использование рациональной формулы Горячкина для аналитического определения тягового сопротивления глубокорыхлителей, в традиционном ее представлении является неуместным, поскольку чизельные агрегаты осуществляют принципиально иную технологическую операцию по сравнению с отвальным плугом. Предложена методика определения тягового сопротивления чизельных орудий с учетом зон деформаций от конструктивных элементов чизельных лап. С практической точки зрения проанализировано влияние некоторых конструктивных элементов глубокорыхлителя на удельное сопротивление почвы и проведена оценка расхода топлива в зависимости от комплектации агрегата. The influence of structural and technological parameters of operating elements of combined deep tillers on the ploughing resistance of the components has been assessed in the article. The objective of the work is to study the influence of the structural and technological parameters of the operating elements of a deep tiller on the ploughing resistance and the estimation of fuel consumption, depending on the configuration of the unit and the set of operating elements during the operation of the combined chisel assemblies. It has been proved that the application of Goryachkin’s rational formula for the analytical determination of the ploughing resistance of deep tillers, in its traditional presentation, is inappropriate, since chisel components undertake a fundamentally different technological operation in comparison with the moldboard plow. The methodology of identification of the ploughing resistance of chisel devices, taking into account deformation zones from constructive elements of chisel tips, was suggested. We received the equation of the resistance of a chisel operating element with the direct stand and additional horizontal deformers, taking into account normal forces, frictional forces, speed of the machine and tractor assembly, and other factors. On the basis of the experimental data, the influence of some structural elements of the deep tiller on the specific resistance of soil was analyzed and the fuel consumption has been estimated depending on the assembly of the device.Item Вплив параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу(ЦНТУ, 2021) Сало, В. М.; Лещенко, С. М.; Богатирьов, Д. В.; Salo, V.; Leshchenko, S.; Bohatyrov, D.В роботі проводиться оцінка параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу. Проаналізовано існуючі конструкції котків- подрібнювачів рослинних решток та обґрунтовано взаємозв’язок окремих конструктивних та технологічних параметрів подрібнювачів на якісні показники їх роботи і можливість забивання міжножового простору. Проведені експериментальні дослідження по оцінці впливу кута розхилу між сусідніми ножами та робочої швидкості агрегату на ймовірність забивання міжножового простору. Доведено, що підвищення швидкості руху подрібнювачів та збільшення кута розхилу між ножами сприяють зменшенню забивання міжножового простору рослинно-ґрунтовою масою навіть при підвищеній вологості. The paper presents the assessment of the parameters of a chopping rotor for shredding plant residues for the reliability of the technological process. The general objective of the work is to substantiate the design and experimental identification of rational parameters of crimp-rollers of plant residues based on the condition of preventing clogging of the inter-knife space with plant-soil mass. The existing designs of crimp-rollers of plant residues are analyzed and the interrelation of certain constructive and technological parameters of shredders on qualitative indicators of their operation and possibility of clogging of inter-knife space is substantiated. The design of a large diameter crimp-roller provides simultaneous full contact with soil of two and sometimes three knives, which during the operation of the roller, together with cutting stems, provides them clamping with soil particles between adjacent knives. The probability of clogging between knives with plant and soil mass increases sharply with the humidity level of the material. Experimental studies have been conducted to assess the effect of the angle of inclination between adjacent knives and the operating velocity of the unit on the probability of clogging the inter-knife space. It is proved that increasing the speed of the shredders and increasing the decay angle between the knives help to reduce clogging of the inter-knife space with plant-soil mass, even at high humidity. The introduction of technological processes of effective preparation of plant residues in the production of crop products will allow starting the system of soil conservation at a farm. It is most expedient to grind plant residues with driveless roller shredders, the main operating parts of which are rollers with knives mounted on the cylinder, and depending on the purpose, quantity and type of plant residues, rollers with large and small diameters are practically used. When shredding high-stem plant residues, it is recommended to use crimp-rollers of large diameter with the following parameters: speed of the unit is 7…8 m/s, the decay angle between adjacent knives is 42… 46º. These parameters of the crimp-roller of plant residues reduce the probability of clogging the inter-knife space to 8%.Item Дослідження руху рослинних решток по горизонтальній частині стеблевідводу сошника(КНТУ, 2011) Лузан, О. Р.; Сало, В. М.; Гончаров, В. В.; Лузан, П. Г.; Luzan, E.; Salo, V.; Goncharov, V.; Luzan, P.В статті теоретично обґрунтовано умови руху рослинних решток по горизонтальній частині стеблевідводу сошника. Отримані рівняння для визначення сприятливих умов, при яких вони відводяться в бік від стояка сошника. Теоретично визначена оптимальна форма стеблевідводу. In the article theoretically grounded traffic conditions plant residues on the horizontal part of the vomer. Obtain equations for determining favorable conditions under which they are assigned to the side of the rack vomer. Theoretically defined optimal form.Item Експериментальні дослідження впливу швидкості руху котка-подрібнювача на якість подрібнення рослинних решток соняшнику(КНТУ, 2014) Богатирьов, Д. Б.; Сало, В. М.; Мачок, Ю. В.; Bohatyrov, D.; Salo, V.; Machok, Y.Наведений напрям розробки та удосконалення сільськогосподарських машин для подрібнення рослинних решток в Україні є новим та дуже актуальним. Представлено аналіз результатів польових випробовувань котка-подрібнювача вітчизняного виробництва. Основним показником роботи даної машини обрано співвідношення розмірів решток стебел соняшнику після подрібнення в залежності від швидкості руху агрегата. Наведені результати випробовувань свідчать про доцільність використання даного типу сільськогосподарської техніки. Agrarian economy of Ukraine and the global trend of environmentally friendly crop production leads to the search for new technologies of crop growing and developing the necessary technology. The need for fertilizers feed plants is always topical issue. Over the past decade, making huge quantities of mineral fertilizers significantly degrade the organic component of topsoil . Also, use of chemicals in agriculture leads to environmental pollution. There are many cases where fertilizers and other chemicals made ill-conceived and sometimes irresponsible. This leads to the accumulation of chemicals in soil, groundwater, excessive content of their crop production , and a food - and food of animal origin. This man-made pollution of fertile soil affects the quality of agricultural products , which can lead to increased morbidity. Widespread use of pesticides has created and specific problems associated with the acquisition of weeds, pests and pathogens resistance to them. Direction of development of agricultural machinery for crushing plant residues in Ukraine is a little known but very important. The analysis of the results of field testing of the roller-crusher. The main indicator of this unit size selected residues of sunflower stalks after shredding. The results of the tests indicate the feasibility of using this type of agricultural machinery.Item Експоненційна та мультиплікативна регресійні моделі процесу пневмосепарації зернових сумішей(КНТУ, 2012) Лещенко, С. М.; Сало, В. М.; Васильковський, О. М.; Петренко, Д. І.; Кузло, В. В.; Leschenko, S.; Salo, V.; Vasil'kovskiy, A.; Petrenko, D.; Kuzlo, V.Робота присвячена підвищенню ефективності роботи зерноочисних машин загального призначення шляхом розробки універсальної регресійної моделі процесу очищення зерна повітряним потоком. Отримання адекватної моделі із зменшеною кількістю наближень і припущень дозволить більш ефективно вдосконалити процес очистки. В статті проведено побудову експоненційної та мультиплікативної регресійних моделей процесу сепарації. Запропоновано системний узагальнений аналіз факторів, що впливають на кількісні і якісні показники сепарації. Після використання π – теореми Букінгама, виведені регресійні моделі очищення зернових сумішей повітряним потоком, які є дійсними як для вертикальних, так і для похилих пневмосепаруючих систем. Аналіз безрозмірних комплексів в критеріальному рівнянні для вхідних перемінних дозволяє зменшити їх кількість, при цьому значно скоротити кількість дослідів та зменшити похибку. Work is sanctified to the increase of efficiency work grain cleaners of general-purpose by development of universal regressive model process cleaning of grain by the current of air. The receipt of adequate model with the diminished amount of approaching and suppositions will allow more effectively to perfect a cleaning process. In the article a construction is conducted by exponential and multiplicative regressive models of process separation. The generalized analysis systems of factors that influence on the quantitative and quality indexes separation offers. After the use π - theorems of Bookingamm, the regressive models cleaning of grain mixtures are shown out by the current of air, that are actual as for vertical so for the sloping air systems. The analysis of dimensionless complexes in criterion equalization for entrance variables allows to decrease their amount, here considerably to shorten the amount of experiments and decrease an error.Item Навісний подрібнювач стебел(2010-03-10) Лушніков, В. М.; Златопольський, Ф. Й.; Матвєєв, К. Д.; Сало, В. М.; Сисоліна, І. П.; Лещенко, С. М.; Lushnikov, V.; Zlatopolskyi, F.; Matvieiev, K.; Salo, V.; Sysolina, I.; Leschenko, S.Навісний подрібнювач стебел, який складається із рами, опорних коліс, валів з жорстко закріпленими на них дисковими ножами та роторами, механізму приводу валів, які розташовані по напрямній руху машини та закріплені на рамі, при цьому дискові ножі жорстко закріплені на передніх кінцях валів, а ротори жорстко закріплені на валах між опорами, який відрізняється тим, що вали роторів розташовані горизонтально на відстанях, які визначаються за допомогою діаметра дискових ножів, дискові ножі мають вигляд диска з жорстко з'єднаними з ним ріжучими елементами, які складають з діаметром диска кут a=100...150°, ротори мають вигляд жорсткого диска з шарнірно закріпленими пластинами (молотками), на парних та непарних (сусідніх) валах ротори розташовані в різних площинах обертання.Item Навісний подрібнювач стебел(КДТУ, 2003-04-15) Сисолін, П. В.; Сало, В. М.; Сисоліна, І. П.; Солових, Є. К.; Аулін, В. В.; Труш, М. М.; Лізунов, С. М.; Sysolin, P.; Salo, V.; Sysolina, I.; Solovykh, Y.; Aulin, V.; Trush, M.; Lizunov, S.Навісний подрібнювач стебел складається із рами з закріпленими на ній валами з роторами, механізму приводу та опорних коліс. Вали роторів розташовані по напрямній руху машини і нахилені відносно поверхні поля під гострим кутом своїми передніми кінцями, на передніх верхніх кінцях яких жорстко закріплені дискові ножі. При цьому ротори жорстко закріплені на задніх нижніх кінцях валів. Навесной измельчитель стеблей состоит из рамы с закрепленными на ней валами с роторами, механизма привода и опорных колес. Валы роторов расположены по направляющей движения машины и наклонены относительно поверхности поля под острым углом своими передними концами, на передних верхних концах которых жестко закреплены дисковые ножи. При этом роторы жестко закреплены на задних нижних концах валов. A mounted stem cutter consists of a frame, having shafts with rotors, fixed thereon, a drive mechanism and supporting wheels. The shafts of the rotors are placed along a guide of the motion of the machine and are inclined with the fore ends thereof, on the fore upper ends of which disk knives are rigidly fixed, at acute angle as regards to the surface of the field. In doing so the rotors are rigidly fixed on the rear lower ends of the shafts.Item Обґрунтування перспективних напрямів конструкцій подрібнювачів рослинних решток(КНТУ, 2012) Богатирьов, Д. В.; Сало, В. М.; Носуленко, В. І.; Мартиненко, Д. В.; Bohatyrov, D.; Salo, V.; Nosulenko, V.; Martunenko, D.Наведений аналітичний огляд сучасного стану розвитку конструкцій подрібнювачів рослинних решток. Зроблено спробу встановити шляхи вдосконалення існуючих конструкцій подрібнювачів для раціонального використання на території України. The analytical review of the current state of development of constructions shredder plant residues. An attempt to establish ways to improve existing structures shredders for efficiency in Ukraine.Item Оцінка енергоємності глибокого обробітку ґрунту комбінованими чизельними глибокорозпушувачами(ЦНТУ, 2018) Лещенко, С. М.; Сало, В. М.; Петренко, Д. І.; Лещенко, С. Н.; Петренко, Д. И.; Leshchenko, S.; Salo, V.; Petrenko, D.В роботі проводиться оцінка енергоємності основного обробітку ґрунту комбінованими чизельними глибокорозпушувачами. Доводиться, що незважаючи на значну кількість досліджень у напрямку скорочення витрат енергії на основний обробіток ґрунту, питання залишається актуальним, а з врахуванням необхідності впровадження ґрунтозахисних технологій, найбільш доцільним є оптимізація енерговитрат при проведенні безполицевого обробітку ґрунту комбінованими чизельними ґлибокорозпушувачами. В результаті проведених досліджень доведено можливість скорочення енерговитрат на основний обробіток ґрунту при використанні комбінованих чизельних глибокорозпушувачів із додатковими деформаторами за умови їх ефективного агрегатування з енергетичними засобами. Спираючись на результати практичного використання таких агрегатів розроблені рекомендації щодо їх подальшого використання та вдосконалення В работе проводится оценка энергоемкости основной обработки почвы комбинированными чизельными глубокорыхлителями. Доказывается, что несмотря на значительное количество исследований в направлении сокращения затрат энергии на основную обработку почвы, вопрос остается актуальным, а с учетом необходимости внедрения почвозащитных технологий, наиболее целесообразным является оптимизация энергозатрат при проведении безотвальной обработки почвы комбинированными чизельными глубокорыхлителями. В результате проведенных исследований, доказана возможность сокращения энергозатрат на основную обработку почвы при использовании комбинированных чизельных глубокорыхлителей с дополнительными деформаторами, при условии их эффективного агрегатирования с энергетическими средствами. Опираясь на результаты практического использования таких агрегатов, разработаны рекомендации по их дальнейшему использованию и усовершенствованию The work presents the assessment of energy intensity of the basic soil cultivation with combined chisel deep tillers. It is proved that despite a significant amount of research in the sphere of reducing energy consumption for basic soil cultivation, the issue remains relevant, and taking into account the necessity to apply soil protection technologies, the optimization of energy consumption in the process of subsoil tillage with combined chisel deep tillers becomes most significant. At the stage of the analysis of the conducted studies it has been confirmed that the most effective indicator of the assessment of energy expenditure for soil cultivation is the consumption of fuel, and the change in the geometrical parameters of the working parts is inevitably connected with the dilemma "traction resistance - quality of cultivation". It is clear that reducing traction resistance, as a rule, leads to the deterioration in the quality of soil cultivation and vice versa. Therefore, when designing soil cultivating machines it is necessary to clearly define their principal characteristics. As a result of the conducted research the possibility of reduction of energy consumption for the basic tillage with the application of combined chisel deep tillers with additional deformers is proved. This happens under the condition of effective aggregation with energy means. Based on the results of practical use of such units, recommendations for their further use and improvement were developed. Chisel tillers CHN of domestic production, working bodies of which have chisel paws with flat wings and teeth and dual gears, while working on complicated soils of central Ukraine with an average fuel consumption of about 18 l/ha, at a depth of 35 cm or more ensure the qualitative index of soil crush is 70 ... 75%.Item Оцінка ефективності внесення туків підґрунтовим способом під ярий ячмінь(КНТУ, 2014) Дейкун, В. А.; Сало, В. М.; Васильковський, О. М.; Лещенко, Л. М.; Шепілова, Т. П.; Deykun, V.; Salo, V.; Vasilkovskiy, А.; Leschenko, S.; Shepilova, T.В статті наведені результати визначення ефективності підґрунтового внесення гранульованих мінеральних добрив у польових умовах. Здійснено порівняння запропонованого способу удобрення з класичним розкидним та встановлено раціональну норму внесення туків. The paper presents the results of determining the effectiveness of subsoil introduction granular mineral fertilizers in the field. To improve the efficiency of mineral fertilizers plants at the Department of Agricultural Engineering Kirovohrad National Technical University substantiated parameters and original design created fertilizer spreader device that allows high-quality disperse granular fertilizers in by paw space. Field tests of the proposed device fertilizer spreader conducted in Kirovohrad region. During the execution of sowing angle to the horizontal working body was 1, since this was made tillage to a depth of 8 cm (light disc harrows, combined with toothed). Working bodies were equipped spreader of parameters that provide the bulk supply of seed to a distance of 10 cm from the axis of the leg. After germination index uniformity determined by the classical method. Analysis of studies have shown that entering mineral fertilizers using tiller, equipped working with substantiated authority in the parameters is more effective than the traditional method of surface scattering and reduces the norms of their use by 40% compared with the recommended method when making scattering. In the article the results of determination of efficiency subsoil bringing of granular mineral fertilizers are presented in the field terms. Comparing of an offer subsoil method bringing different norms of complex fertilizers is executed to classic on an area 1,7 ha. During experiments efficiency of subsoil method bringing granular mineral fertilizers is set on the productivity of fervent barley. In addition, the got results of experiments testify to possibility of substantial decline norm bringing granular mineral fertilizers without the loss of the productivity.Item Оцінка ефективності глибокого безполицевого обробітку ґрунту(ЦНТУ, 2020) Лещенко, С. М.; Сало, В. М.; Петренко, Д. І.; Leshchenko, S.; Salo, V.; Petrenko, D.; Лещенко, С. Н.; Петренко, Д. И.В роботі проводиться оцінка ефективності глибокого безполицевого обробітку ґрунту аналітичними методами. Проаналізовано існуючі дослідження взаємодії робочих органів ґрунтообробних машин та знарядь з ґрунтом та систематизовано уявлення про представлення ґрунту в теоретичних моделях в вигляді стохастичного процесу послідовних зіткнень поверхні робочого органу із суцільним середовищем, властивості якого задаються певними характеристиками, що описуються відомими законами розподілу. Запропоновано проводити оцінку якості роботи ґрунтообробних машин і знарядь відсотковим вмістом за масою у ґрунті агрегатів заданого розміру та ступенем подрібнення ґрунту. The paper presents the evaluation of effectiveness of deep chiseling with the help of analytical methods. General objective of the work is to develop the method for describing theoretical interaction of operating parts of machines and tools with soil during main chiseling in the form of a stochastic process of successive hits of the operating part with a solid medium. The destruction of monoliths (uncultivated) soil during its cultivation was considered as a process of formation and subsequent evolution of dynamic cracks, the nature and amount of which, in a particular soil volume, is determined by the amount of energy absorbed by operating parts and the actual properties of cultivated soil. It should be taken into consideration that the spread of cracks during chiseling occurs by the lowest strength of connections between certain structural units, in fact organic inclusions, soil pores, moisture inclusions and other similar elements are the largest centers of formation, concentration and further development of cracks during cultivation. Interaction of operating parts of machines and tools with soil is most expedient to carry out modeling work in a thickness of the environment of a dihedral wedge taking into account mechanical structure of soil. It is established that the number of cracks and the size and number of lumps after cultivation are linearly dependent, which means that to qualitatively study the change in physical state, during chiseling with operating parts and tools, it is enough to study the process and evolution of cracking. As a result of the work performed, it is proved that the degree of soil grinding during its chiseling can be assessed by probability, and the quality of tools, that is the percentage of total mass of cultivated soil particles with the size not exceeding 50 mm. When modeling chiseling, the grinding process can be considered in the form of interaction of a dihedral wedge with a solid structured layer of soil with specified properties. The interaction of the chiseling operating part with the soil is accompanied by deformation of soil environment, increased stresses and cracks, which ultimately determine the shape and size of the crushed units. We believe that the number and nature of cracks that occur during tillage are in direct proportion to the size of the obtained units upon completion. В работе проводится оценка эффективности глубокой безотвальной обработки почвы аналитическими методами. Проанализированы существующие исследования взаимодействия рабочих органов почвообрабатывающих машин и орудий с почвой и систематизированы суждения о представлении почвы в теоретических моделях в виде стохастического процесса последовательных столкновений поверхности рабочего органа со сплошной средой, свойства которой задаются определенными характеристиками, которые описываются известными законами распределения. Предложено проводить оценку качества работы почвообрабатывающих машин и орудий процентным содержанием по массе в почве агрегатов заданного размера и степенью измельчения грунта.