Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
7 results
Search Results
Item Використання мікродугового оксидування при зміцненні деталей з алюмінієвих сплавів, відновлених пластичним деформуванням(ЦНТУ, 2017) Кулєшков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Матвієнко, О. О.; Kuleshkov, Y.; Krasota, M.; Rudenko, T.; Matvienko, A.У статті приведений аналіз можливості використання нового способу зміцнення - мікродугового оксидування для підвищення зносостійкості деталей, виготовлених з алюмінієвих сплавів, зокрема корпусів шестеренних насосів типу НШ. У роботі викладена сутність процесу зміцнення деталей мікродуговим оксидуванням, представлені основні фізико-механічні характеристики зміцнюючого покриття. Відзначено, що міцність зчеплення і механічні властивості покриття багато в чому залежать від стану поверхні, що зміцнюється, зокрема від методу попередньої обробки. При цьому встановлено, що зміцнюючі покриття після пластичного деформування деталей мають вищу міцність зчеплення, твердість і більшу товщину. У роботі представлені основні відомості про мікродугове оксидуванні, які на думку авторів будуть сприяти застосуванню маловивченого способу зміцнення в ремонтному виробництві. The objective of the research is to analyse the scientific and technical information on hardening of parts of aluminium alloys by micro-arc oxidation, particularly the parts, which were repaired by hot plastic deformation. This article presents the analysis of the possibility to apply a new method of hardening of working surfaces of parts by micro-arc oxidation to increase wearability of working surfaces of the parts made of aluminium alloys, in particular the bodies of gear pumps. The work presents the essence of the process of hardening of details by micro-arc oxidation and the main physical and chemical characteristics of the hardening coating. It was stated that the adhesive strength and mechanical characteristics of the coating largely depend on the condition of the surface under hardening, in particular on the method of preparatory processing. It was established that the hardening coating of metal after plastic deformation gets better adhesive strength, thickness and hardness. The work presents basic information on micro-arc oxidation which will facilitate further application of the hardening method in repair industry.Item Математична модель втрат робочої рідини через радіальний зазор шестеренного насоса типу НШ(КНТУ, 2005) Матвієнко, О. О.; Matvienko, OleksandrВ статті розглянуто змінний характер величини зони ущільнення радіального зазору шестеренного насоса типу НШ і на основі отриманих результатів створено математичну модель втрат робочої рідини через радіальний зазор. There is analysis variable parameter of compaction area of radial clearance in gear pumps of НШ-type. The author of the article derive the simulator for calculation a radial leak on the basis of findings.Item Аналіз математичних моделей втрат робочої рідини через радіальний зазор шестеренного насоса типу НШ(КНТУ, 2006) Кулєшков, Ю. В.; Матвієнко, О. О.; Kuleshkov, J.; Matvienko, O.В статті розглянуто відомі математичні моделі втрат робочої рідини через радіальний зазор шестеренного насоса типу НШ і зроблено аналіз їх переваг та недоліків. In the article the mathematical models known working fluid leaks through the radial clearances of gear pumps and the analysis of their strengths and weaknesses.Item Методика стендових випробовувань шестеренного насоса(КНТУ, 2011) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвієнко, О. О.; Титов, Ю. А.; Kuleshkov, J.; Rudenko, T.; Krasota, M.; Matvienko, A.; Titov, J.Розроблена програма досліджень, яка включала методики дослідження основних технічних характеристик НШ для різних значень тиску, робочого об’єму насоса і частоти обертання, і перевірку ступеня збігу основних теоретичних положень і висновків з результатами, отриманими експериментальним шляхом. Розглянуто методики випробувань шестеренних насосів з регульованою подачею, наведено будову та характеристика дослідного обладнання. Викладено методику обробки даних, отриманих при проведенні експериментальних досліджень. The program of researches including techniques of research of basic tehniche-skih of characteristics gear-type pumps for different values of pressure, working volume of the pump and frequency of rotation, check of degree of coincidence of the basic theoretical positions and conclusions with the results, luchen th experimentally is developed. Techniques of tests gear-type pumps from a reguliro-bathroom are considered by giving, the device and the characteristic of the research equipment is resulted. The technique of the data processing, the experimental researches received at carrying out is stated.Item Анализ эффективности существующих и перспективных методов обработки деталей с покрытиями(КНТУ, 2014) Красота, М. В.; Шепеленко, И. В.; Матвиенко, А. А.; Аль Соодани Салем М. Муташаир; Krasota, Mykhailo; Shepelenko, Ihor; Matvienko, Oleksander; Al Soodani Salem M. Mutashair; Шепеленко, І. В.; Матвієнко, О. О.; Аль Соодані Салем М. МуташаїрВ статье рассмотрены основные методы обработки деталей с покрытиями, полученными методами наплавки, напыления и наварки. Проанализированы достоинства и недостатки этих методов, определены области применения. Установлены тенденции применения механических видов обработки покрытий, находящихся в нагретом состоянии. Выполнен анализ научных работ в направлении механической обработки покрытий в горячем состоянии. В статті розглянуті основні методи обробки деталей з покриттями, отриманими методами наплавлення, напилювання і наварювання. Проаналізовані переваги та недоліки цих методів, визначені галузі застосування. Встановлені тенденції застосування механічних видів обробки покриттів, що знаходяться в нагрітому стані. Виконаний аналіз наукових робіт в напрямку механічної обробки покриттів в гарячому стані. Application of wear-proof coverings while hardening and renewal of machine parts facilitates the increase of their reliability but at the same time it makes their treatment in cold working more complicated. Coverings have high level of hardness and its uneven distribution in the length of a part, a heterogeneous structure, a big height of lugs and cavities of the hard-facing layer. The objective of the work is to analyse current and perspective technologies of treatment of wear-proof coverings. The research has been done on most extensive treatment technologies of covered parts which are used in machine building today. They include cutting treatment (turning, milling, grinding), shaping, electro-physical and electrochemical methods. It was defined that they have a range of disadvantages and are not always efficient. Parts that have covering hardness more that 40 HRC can be effectively treated using the technologies of treatment of cutting methods such as grinding and turning of upper plastic deformation using residual heat after hard facing, spraying or welding on. Treatment of coverings in heated conditions allows decreasing cutting force and increasing productivity of treatment and improving parameters of quality of treated surfaces.Item Экспериментальные исследования спектров шума шестеренного насоса с косозубым зацеплением(КНТУ, 2015) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвиенко, О. О.; Осин, Р. А.; Kuleshkov, Y.; Rudenko, T.; Krasota, M.; Matvienko, O.; Osin, R.; Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвієнко, О. О.; Осін, Р. А.В статье приведены результаты испытаний шумовых характеристик экспериментального шестеренного насоса с косозубым зацеплением. Исследованы уровни звука, спектры шума. экспериментального насоса с косозубым зацеплением, а также серийного насоса аналогичного типоразмера при разных режимах их работы. Выполнен сравнительный анализ шумовых характеристик насосов при разных нагрузках с целью оценки эффективности использования косозубых зацеплений в шестеренных насосах с точки зрения снижения шума. В статті наведені результати випробовувань шумових характеристик експериментального шестеренного насоса з косозубим зачепленням. Досліджено рівні звуку, спектри шуму експериментального шестеренного з косозубим зачепленням, а також серійного насосу аналогічного типорозміру при різних режимах їх роботи. Виконано порівняльний аналіз шумових характеристик насосів при різних навантаженнях з метою оцінки ефективності використання косозубих зачеплень в шестеренних насосах з точки зору зниження шуму. The objective of the work is the experimental testing of the noise level by the lines of spectrum of the experimental gear pump with helical toothing and the comparison with the noise level of a serial pump. The article presents the results of tests of noise characteristics of the experimental gear pump with helical toothing. The levels of noise, noise spectrums of the experimental gear pump with helical toothing and a serial pump of the analogical size with straight toothing were investigated using different operating modes. The comparative analysis of noise characteristics of the pumps under different load was carried out in order to estimate the efficiency of using helical toothing in gear pumps from the point of view of noise reduction. Experiments of the noise level of a gear pump with helical toothing showed that with the increase of pressure of hydraulic fluid the level of noise slowly increases from 1,5 to 6 dB depending on speed mode. The highest noise level of a pump with helical toothing (91,5 dB ) is noticed under the pressure of 16,0 MPa and rotation frequency n=2400 revolutions per minute. The comparative analysis of the experimental pump and a serial pump enables to state that the noise level of the experimental pump is lower in all operating modes compared to the serial pump. During tests it was marked that the noise level of the stand which is a barrier is quite high and under some operating modes it is close to the noise level of the experimental pump on the stand.Item Вплив автомобільного транспорту на повітряний басейн міста Кіровограда(КНТУ, 2015) Бевз, О. В.; Магопець, С. О.; Матвієнко, О. О.; Bevz, Oleg; Magopec, Sergiy; Matvienko, OlexandrОбґрунтована актуальність проблеми екологічної безпеки автомобільного транспорту, вплив його на довкілля і проаналізовано дві основні транспортні магістралі, які впливають на забруднення атмосферного басейну міста Кіровограда. In this work considered problems of ecological safety of motor transport, influence of him on an environment and it is analyses two basic transport highways which influence on contamination of atmospheric pool of city of Kirovograd. Researches are directed on determination of degree of work-load of a main transport highway of city of Kirovograd and level of extrass on them. Basic directions of decline of level of contamination of environment of city of Kirovograd from a motor transport is organization of rational chart of routes of motion of passenger and freight streams of city.