Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
10 results
Search Results
Item Розрахунок не зрівноважено утримуваних деталей захватними пристроями роботів(ЦНТУ, 2019) Павленко, І. І.; Годунко, М. О.; Павленко, И. И.; Годунко, М. О.; Pavlenko, I.; Hodunko, M.Виконано обґрунтування розрахунку сил затиску в захватному пристрої робота при утриманні деталей зі зміщеним центром мас. Виведено формули для розрахунку даних сил. Встановлено залежності між основними конструктивними характеристиками захватного пристрою та силами затиску. Выполнено обоснование расчета сил зажима в захватном устройстве робота при содержании деталей со смещенным центром тяжести. Выведены формулы для расчета данных сил. Установлены зависимости между основными конструктивными характеристиками захватного устройства и силами зажима. The substantiation of the calculation of the clamping forces in the gripping device of the robot with the maintenance of parts with an offset center of gravity. The formulas for calculating these forces are derived. Dependencies between the main design characteristics of the gripping device and the clamping forces are established. Grippers are one of the responsible executive bodies of industrial robots. Their main feature is that they represent a finite part of the spatially unlocked hand of the robot, which must perform high-speed reciprocating (rotating) movements with the required accuracy. In this case, the grip must reliably hold the transported parts with a minimum of their mass. All this is possible when performing their exact calculations. In a large number of robots of capture operations, it is necessary to keep parts that are not evenly squeezed into it. This may take place, both during initial capture and during the cycle of the operation of work with the detail when it sets it on a machine where it is processed and gets a different shape and size. All these features lead to a change in the power load on the gripper, and, accordingly, to change the working capacity of its quality. The first step in the study of these issues is to determine the required clamping forces of the retained parts. To do this, taking into account all baseline conditions, we compile a calculation scheme, where the detail is clamped with the capture with an asymmetric (not balanced) its placement. In earlier studies, it was found that in determining the forces of clamping of parts, according to such calculation schemes, there may be a condition where the number of complicated equations of equilibrium of the held part is less than the number of unknown clamping forces. Therefore, an additional condition was adopted for solving the task, when the minimum required clamping forces were determined, which then increased to the required stock factor. The same condition we accept in these calculations.Item Аналіз та синтез кінематико-силової структури захватних пристроїв(КНТУ, 2011) Павленко, І. І.; Годунко, М. О.; Pavlenko, І.; Godunko, М.У даній статті описано методику дослідження будови захватних пристроїв роботів на структурному рівні. Також приведені кінематичні схеми та структурні формули для типових варіантів виконання захватів. Запропоновано кінематико-силові схеми та формули балансу сил захватних пристроїв різних виконань. In this article the method of research of structure of grippers of robots is described at structural level. Kinematics charts and structural formulas are also resulted for the typical variants of implementation of grippers. Kinematics-forces charts and formulas of balance of forces of capture devices of different implementations are offered.Item Показники оцінки якості захватних пристроїв промислових роботів(КНТУ, 2007) Павленко, І. І.; Годунко, М. О.В даній статті наведена система показників якості захватних пристроїв промислових роботів, яка дає можливість комплексно оцінювати якість виконання та функціонування захватів, а також порівнювати якість різних захватних пристроїв та вплив окремих факторів їх будови та роботи.Item Аналіз впливу характеристик захватних пристроїв промислових роботів на силові їх навантаження(КНТУ, 2008) Павленко, І. І.; Годунко, М. О.В даній статті наведено приклади силових розрахунків захватних пристроїв при розміщенні їх у різних площинах та різних напрямках руху. Це дає змогу порівняти варіанти затиску деталі та дослідити вплив конструктивних та функціональних характеристик захватних пристроїв промислових роботів на сили затиску. In this article the examples of power calculations of Grippers are resulted at placing of them in different planes at the change of orientation the landmark of detail. It enables to compare the variants of clamp of detail and probe influence of geometrical parameters at their change on forces of clamp.Item Експериментальні динамічні дослідження сил затиску захватних пристроїв промислових роботів(КНТУ, 2010) Павленко, І. І.; Годунко, М. О.; Pavlenko, І.; Godunko, М.У даній статті описано експериментальні динамічні дослідження сил затиску захватних пристроїв промислових роботів, які підтверджують правильність раніше виконаних теоретичних розрахунків. Також у статті показано графіки, що виводились на монітор комп’ютера при вимірюванні сил затиску для горизонтального руху руки робота та побудовано експериментальні і розрахункові криві відповідних залежностей. Dinamic researches of forces of clamp of gripper of industrial robots which confirm the rightness of the before described theoretical calculations are described in this article. Also the graphs which hatched on the monitor of computer at measuring of forces of clamp for the platforming of hand of robot and the experimental and calculation curves of the proper dependences are built are rotined in the article.Item Функціональні характеристики затискних важелів захватних пристроїв роботів(КНТУ, 2010) Павленко, І. І.; Годунко, М. О.; Pavlenko, І.; Godunko, М.У даній статті описано спосіб визначення передавальних відношень, що забезпечуються затискними важелями захватного пристрою. Також у статті розглянуто схеми затиску з різними значеннями діаметрів деталі, а також з різними конструктивними параметрами затискних важелів. Результати розрахунків зведено в загальну таблицю. The method of determination of transmission relations which are provided the clamping levers of grippers is described in this article. Also in the article the charts of clamp are considered with the different values of diameters of detail, and also with the different structural parameters of clamping levers. The results of calculations are erected in a general table.Item Конструктивна та силова структура захватних пристроїв промислових роботів(КНТУ, 2006) Павленко, І. І.; Годунко, М. О.В даній статті запропонована конструктивна та силова структура захватних пристроїв промислових роботів, яка враховує структурні особливості будови захватів та силового затиску деталей. Також виділено вимоги до створення і функціонування захватних пристроїв промислових роботів. Constructive and power structure of seazing devises of industrial robots is considered in this article. The article deals with the constructive peculiarities of the seazing devices and power clamp of parts. It also gives a description of creation and functioning of clamping devices of industrial robots.Item Аналіз передавальних відношень плеч сил затискних важелів захватних пристроїв роботів(КНТУ, 2010) Павленко, І. І.; Годунко, М. О.; Pavlenko, I.; Godunko, M.У даній статті описано аналіз впливу складових плеч сил затискних важелів захватних пристроїв промислових роботів. Також у статті наведено графіки впливу визначених складових, які побудовані для умов реальної можливості утримування деталі захватними важелями. По отриманим залежностям зроблено практичні висновки. The analysis of influence of making shoulders of forces of clamping levers of grippers of industrial robots is described in this article. Also the graphs of influence of certain constituents which are built for the terms of the real possibility of retaining of detail clamping levers are resulted in the article. On the got dependences conclusions are done.Item Аналіз впливу конструктивних параметрів захватних пристроїв роботів на сумарні сили затиску деталей(КНТУ, 2008) Павленко, І. І.; Годунко, М. О.В даній статті наведено приклад розрахунку сумарних сил затиску захватних пристроїв при вертикальному його розміщенні і дії сили інерції під певним кутом. Це дає змогу дослідити процес затиску деталі та вплив конструктивних, а також функціональних характеристик захватних пристроїв промислових роботів на сумарні сили затиску. In this article the example of calculation of total forces of clamp of grippers is resulted at his vertical placing and action of force of inertia under a certain corner. It enables to probe the process of clamp of detail and influence structural, and also functional descriptions of grippers of industrial robots on total forces of clamp.Item Експериментальні статичні дослідження сил затиску захватних пристроїв промислових роботів(КНТУ, 2009) Павленко, І. І.; Годунко, М. О.В даній статті описано експериментальні статичні дослідження сил затиску захватних пристроїв промислових роботів, які підтверджують правильність раніше виконаних теоретичних розрахунків. Static researches of forces of clamp of gripper of industrial robots which confirm the rightness of the before described theoretical calculations are described in this article.